Energy and utilitiesSDWAN Lite
Secure remote access and monitoring for wind turbines
Wind turbines stand where the wind is, not where fibre is, and turbine makers need access to controllers for diagnostics. Instaroute routers connect turbine and substation controllers over dual-SIM 4G, carry SCADA protocols to the control centre in encrypted tunnels, and let vendors reach only the turbines they support through logged ZTNA sessions.
By Pradeep Tomar, Founder and CEO. Published , last reviewed .At a glance
- Industry
- Renewable energy (wind)
- Sites
- Wind turbines, farms and substations
- Access
- ZTNA, SSL VPN or IPsec VPN, logged
- Routers
- IR1180DM, IR1105-ODU-4G
How does the network connect?
Site equipment connects to an Instaroute IR1180DM, which carries the traffic over SIM 1 · Operator A and SIM 2 · Operator B inside a quantum-safe tunnel to Wind farm control room and Vendor engineers via InstaAccess. Nothing on site accepts inbound connections.
What problem does it solve?
Turbine sites are remote, often without a wired link, and every turbine controller still has to report to the control centre and be reachable for maintenance.
Opening ports or sharing VPN accounts for service partners exposes the whole site network, while every hour a turbine is down costs generation.
Indian wind farms stretch along ridges and coastal belts, with turbines spread over many kilometres of farmland. Mobile coverage changes from one location to the next: one operator may be strong at the pooling substation and weak at the far end of the farm. Turbines and substations also come from different makers and different phases of a project, each with its own service team asking for access.
How does Nexapp solve it?
Cellular connectivity and secure vendor access for wind turbine controllers and substations: dual-SIM 4G, IEC 104 and Modbus, logged ZTNA sessions.
Vendor access without open ports
Engineers and equipment vendors connect through the InstaAccess client (ZTNA, SSL VPN or IPsec VPN) to only the equipment they support, and every session is logged.
Cellular links that stay up
Instaroute 4G and 5G routers with dual-SIM arbitration by signal, latency or data usage, so two operators back each other up. IP65 outdoor units mount on a pole or mast where the signal is best.
Speaks the site's protocols
RS232/RS485 serial ports, a Modbus RTU/ASCII/TCP gateway, DNP3, IEC 60870-5-101/104 and an MQTT publisher, so existing controllers, RTUs and meters connect without replacement.
Encrypted end to end
IPsec IKEv2 tunnels on NexappOS with hybrid post-quantum key exchange (ML-KEM, NIST FIPS 203), on by default, back to the control centre.
How is the site secured in the AI era?
Security is a requirement, not an add-on. AI helps attackers find exposed devices and weak access faster than ever, so this design exposes nothing, encrypts every link and checks every person who connects.
Nothing exposed to the internet
The router opens only outbound, encrypted connections. Equipment on site has no public IP and accepts no inbound connections, so automated scanners have nothing to find. Zero trust access
Quantum-safe encryption on every link
Traffic travels in IPsec IKEv2 tunnels with hybrid ML-KEM key exchange, so data captured today cannot be decrypted later. Post-quantum cryptography
Zones, not one flat network
Turbine controller and substation RTU sit in their own zones behind the zone firewall, so one compromised device cannot reach the rest. IoT and OT security
Access for people, not networks
Engineers and vendors connect through InstaAccess to the named equipment they support, and every session is logged. SSE and ZTNA
Signed, staged firmware
Instaroute SDWAN Lite 2.0 rolls out post-quantum-signed firmware to a canary group first, with rollback, so a bad update never reaches every site at once. Instaroute SDWAN Lite 2.0
AI that waits for your approval
NexParth AI spots problems and proposes the fix, and nothing changes until a person approves it. NexParth AI
What does the SDWAN Lite dashboard show?
One screen shows the whole fleet: total devices and online rate, WAN links and SIM cards, active alarms, a fleet map, firmware versions, configuration changes, product mix and data usage. Instaroute SDWAN Lite 2.0 manages up to 100,000 routers per deployment, hosted by Nexapp in India or self-hosted.

How is it deployed?
A typical rollout takes 5 steps, and routers configure themselves when they are powered on at site.
Place the router
DIN-rail in the turbine or substation cabinet, or an IP65 outdoor unit on the mast where the signal is best.
Connect the controllers
Turbine and substation controllers connect over serial or Ethernet, speaking IEC 104, DNP3 or Modbus.
Tunnel to the control centre
SCADA traffic travels in an encrypted tunnel; a second operator takes over if the first fails.
Grant vendor access
Turbine makers get access to named turbines only through InstaAccess, never through open ports.
Diagnose remotely
Many faults are investigated from the control room before anyone drives to site.
What does the specification ask for, and how does Nexapp meet it?
These are the requirements buyers and tenders usually set for this application, and the Nexapp capability that meets each one today.
| Requirement | How Nexapp meets it |
|---|---|
| Vendor access without exposing the site | InstaAccess (ZTNA, SSL VPN or IPsec VPN) to named equipment, with session logs |
| Reliable link at remote sites | Dual-SIM arbitration; IR1105-ODU-4G outdoor unit for weak signal |
| SCADA protocol support | IEC 60870-5-101/104, DNP3, Modbus and MQTT |
| Encrypted control traffic | IPsec IKEv2 with hybrid post-quantum key exchange, on by default |
Which Instaroute router should you use?
For most sites, use the IR1180DM. DIN-rail with dual SIM, serial ports and GPS for the turbine or substation cabinet.
Instaroute IR1180DM 4G router IR1180DM 4G · LTE · 2 SIM IR1180DM
DIN-rail with dual SIM, serial ports and GPS for the turbine or substation cabinet.
- Cellular
- 4G LTE Cat 4 or Cat 6
- SIM slots
- 2
- RS232 / RS485
- RS232 and RS485
- Mounting
- DIN-rail
Instaroute IR1105-ODU-4G 4G router IR1105-ODU-4G 4G · OUTDOOR · 2 SIM IR1105-ODU-4G
Outdoor IP65 unit mounted on the mast where the signal is best.
- Cellular
- 4G LTE Cat 4 or Cat 6
- SIM slots
- 2
- RS232 / RS485
- No
- Mounting
- Outdoor, pole or mast
Also used: InstaAccess client (ZTNA, SSL VPN, IPsec VPN) · Instaroute SDWAN Lite 2.0
What are the benefits?
- Vendors reach only the turbines they support, and every session is recorded.
- Many faults are diagnosed remotely, without a site visit.
- Turbine data reaches the control centre over managed links with a second operator ready.
Why choose Nexapp?
- Indian OEM in Pune since 2014, with its own NexappOS and controller
- Class-I local supplier under the PPP-MII Order
- TEC MTCTE certificate 244903206 for nine Instaroute models
- Quantum-safe on every connection: hybrid ML-KEM and ML-DSA
- 24×7 NOC in Pune; hosted in India or self-hosted
- 75,000+ devices deployed for 400+ enterprise and banking customers
Frequently asked questions
How do turbine makers get remote access without exposing the site?
They connect through the InstaAccess client to named turbines only. Nothing on the site network accepts inbound connections, and every session is logged.
Which protocols are supported?
IEC 60870-5-101/104, DNP3, Modbus RTU/ASCII/TCP and MQTT, with RS232/RS485 serial ports.
Which router goes in the turbine or substation cabinet?
The IR1180DM: DIN-rail, dual SIM, RS232/RS485, five Ethernet ports and GPS. Where the cabinet sits in a weak spot, mount the IP65 IR1105-ODU-4G on the mast and connect it over Ethernet; it has no serial ports of its own.
What if coverage differs from turbine to turbine?
Survey each location and pick the SIM pair that works there; the two SIMs can come from different operators. SDWAN Lite 2.0 then reports signal strength and quality per SIM (RSRP, RSRQ, SINR and CSQ) and ranks the worst-signal sites, so weak turbines are found early.
Can a service partner's access be limited to a maintenance window?
Yes. Third parties get time-bound access to named turbines through the InstaAccess client, and every session is logged, so access ends when the work does.
Is the control-room link exposed to the internet?
No. The router builds outbound IPsec IKEv2 tunnels with hybrid post-quantum key exchange, on by default, and nothing on the turbine network accepts inbound connections.
Read next
Planning a similar deployment?
Tell us your sites, devices and links, and a Nexapp engineer will recommend the routers and design.
Related use cases
Energy and utilities
4G router for substation SCADA and RTU/FRTU backhaulIndustrial 4G routers for substations, RTUs and FRTUs: IEC 60870-5-101/104, DNP3, Modbus, serial DTU and encrypted tunnels to the SCADA control centre.
Energy and utilities
Cellular backhaul for smart meters and data concentrator units4G routers for smart-meter data concentrator units (DCUs) and AMR: serial and Modbus interfaces, MQTT, encrypted tunnels and flat per-device management.
Energy and utilities
Remote monitoring and connectivity for solar plantsOne managed network for inverters, meters, weather stations and cameras across solar farms and rooftop plants, with scoped vendor access and one console.