Energy and utilitiesSDWAN Lite

Oil and gas pipeline SCADA monitoring over cellular

Pipelines cross long, remote stretches, and every valve, metering and pumping station has to report pressure, flow and leaks continuously. Instaroute routers carry Modbus, DNP3 and IEC 60870-5-104 data from each station to the SCADA control room over 4G, in IPsec tunnels with hybrid post-quantum key exchange, and are maintained remotely from one console.

At a glance

Industry
Oil and gas
Sites
Valve, metering and pumping stations
Protocols
Modbus, DNP3, IEC 60870-5-104
Routers
IR1180DM, IR1105-ODU-4G

How does the network connect?

Site equipment connects to an Instaroute IR1180DM, which carries the traffic over SIM 1 · Operator A and SIM 2 · Operator B inside a quantum-safe tunnel to SCADA control room. Nothing on site accepts inbound connections.

NEXAPP CLOUD PLATFORMInstaroute SDWAN Lite 2.0Dashboard · alarms · zero-touch · firmwareHosted in India or self-hostedManagement · no public IPYour teamREMOTE SITEMOBILE NETWORK · INTERNETCONTROL CENTREStation RTU / PLCPressure and flowsensorsIR1180DMInstaroute · NexappOSSIM 1 · Operator ASIM 2 · Operator BOperator coreSCADA control roomIPsec IKEv2 · hybrid ML-KEMQuantum-safe tunnel · outbound only, nothing on site accepts inbound connectionsNEXAPP CLOUD PLATFORMInstaroute SDWAN Lite 2.0Dashboard · alarms · firmwareIndia-hosted or self-hostedREMOTE SITEStation RTU / PLCPressure and flow sensorsIR1180DM · InstarouteMOBILE NETWORK · INTERNETSIM 1 · Operator ASIM 2 · Operator BIPsec IKEv2 · hybrid ML-KEMCONTROL CENTRESCADA control room
How it connects: Station RTU / PLC, Pressure and flow sensors at the remote site connect to the IR1180DM 4G. Traffic travels over SIM 1 · Operator A and SIM 2 · Operator B inside a quantum-safe tunnel (IPsec IKEv2 · hybrid ML-KEM) to SCADA control room. The router is managed from the Nexapp cloud platform (Instaroute SDWAN Lite 2.0), hosted in India or self-hosted, over an always-on management channel that needs no public IP.

What problem does it solve?

Stations sit far from towns, so a link failure means lost visibility of pressure and flow, and valves that cannot be commanded.

Equipment has to be reliable and manageable without a visit, and SCADA traffic is critical infrastructure that must be encrypted.

Cross-country pipelines in India pass through farmland, forest and hills, where one operator's coverage can vanish for long stretches and a station may be hours by road from the nearest maintenance base. Changes to station RTUs and PLCs are tightly controlled, so the communication layer has to fit the equipment already commissioned rather than force a redesign of the SCADA system.

How does Nexapp solve it?

Dual-SIM 4G links for pipeline valve, metering and pumping stations: Modbus, DNP3 and IEC 104 data to the SCADA control room in encrypted tunnels.

  • Speaks the site's protocols

    RS232/RS485 serial ports, a Modbus RTU/ASCII/TCP gateway, DNP3, IEC 60870-5-101/104 and an MQTT publisher, so existing controllers, RTUs and meters connect without replacement.

  • Cellular links that stay up

    Instaroute 4G and 5G routers with dual-SIM arbitration by signal, latency or data usage, so two operators back each other up. IP65 outdoor units mount on a pole or mast where the signal is best.

  • Encrypted end to end

    IPsec IKEv2 tunnels on NexappOS with hybrid post-quantum key exchange (ML-KEM, NIST FIPS 203), on by default, back to the control centre.

  • One console for every site

    Instaroute SDWAN Lite 2.0 shows the health, signal and data usage of every router, with zero-touch set-up and canary firmware rollout, for up to 100,000 devices per deployment. Run it Nexapp-hosted in India or self-hosted.

How is the site secured in the AI era?

Security is a requirement, not an add-on. AI helps attackers find exposed devices and weak access faster than ever, so this design exposes nothing, encrypts every link and checks every person who connects.

  • Nothing exposed to the internet

    The router opens only outbound, encrypted connections. Equipment on site has no public IP and accepts no inbound connections, so automated scanners have nothing to find. Zero trust access

  • Quantum-safe encryption on every link

    Traffic travels in IPsec IKEv2 tunnels with hybrid ML-KEM key exchange, so data captured today cannot be decrypted later. Post-quantum cryptography

  • Zones, not one flat network

    Each group of equipment on site gets its own zone behind the zone firewall, so one compromised device cannot reach the rest. IoT and OT security

  • Access for people, not networks

    Engineers and vendors connect through InstaAccess to the named equipment they support, and every session is logged. SSE and ZTNA

  • Signed, staged firmware

    Instaroute SDWAN Lite 2.0 rolls out post-quantum-signed firmware to a canary group first, with rollback, so a bad update never reaches every site at once. Instaroute SDWAN Lite 2.0

  • AI that waits for your approval

    NexParth AI spots problems and proposes the fix, and nothing changes until a person approves it. NexParth AI

What does the SDWAN Lite dashboard show?

One screen shows the whole fleet: total devices and online rate, WAN links and SIM cards, active alarms, a fleet map, firmware versions, configuration changes, product mix and data usage. Instaroute SDWAN Lite 2.0 manages up to 100,000 routers per deployment, hosted by Nexapp in India or self-hosted.

Instaroute SDWAN Lite 2.0 dashboard with device status, WAN and SIM health, alarms, fleet map, firmware distribution and data usage (sample data)
Instaroute SDWAN Lite 2.0 dashboard, shown with sample data. See SDWAN Lite 2.0

How is it deployed?

A typical rollout takes 4 steps, and routers configure themselves when they are powered on at site.

  1. Survey the stations

    Check coverage at each valve, metering and pumping station and choose indoor or outdoor units.

  2. Connect station equipment

    RTUs and PLCs connect over serial or Ethernet with IEC 104, DNP3 or Modbus.

  3. Tunnel to the control room

    Station data travels in encrypted tunnels to SCADA, with a second operator as backup.

  4. Maintain remotely

    Firmware, configuration and signal are managed centrally, without station visits.

What does the specification ask for, and how does Nexapp meet it?

These are the requirements buyers and tenders usually set for this application, and the Nexapp capability that meets each one today.

Typical requirements: oil and gas pipeline scada monitoring over cellular
RequirementHow Nexapp meets it
SCADA protocolsIEC 60870-5-101/104, DNP3, Modbus RTU/ASCII/TCP
Critical-infrastructure encryptionIPsec IKEv2 with hybrid ML-KEM key exchange and ML-DSA authentication
Coverage at remote stationsDual-SIM and the IP65 IR1105-ODU-4G outdoor unit
Manage without site visitsSDWAN Lite 2.0 with an always-on management channel

Which Instaroute router should you use?

For most sites, use the IR1180DM. DIN-rail, dual SIM, serial ports and GPS for station cabinets.

  • Instaroute IR1180DM 4G routerIR1180DM4G · LTE · 2 SIM

    IR1180DM

    DIN-rail, dual SIM, serial ports and GPS for station cabinets.

    Cellular
    4G LTE Cat 4 or Cat 6
    SIM slots
    2
    RS232 / RS485
    RS232 and RS485
    Mounting
    DIN-rail
  • Instaroute IR1105-ODU-4G 4G routerIR1105-ODU-4G4G · OUTDOOR · 2 SIM

    IR1105-ODU-4G

    Outdoor IP65 unit for stations with poor indoor coverage.

    Cellular
    4G LTE Cat 4 or Cat 6
    SIM slots
    2
    RS232 / RS485
    No
    Mounting
    Outdoor, pole or mast

Also used: Instaroute SDWAN Lite 2.0

What are the benefits?

  • Station data reaches the SCADA control room continuously.
  • SCADA traffic is encrypted end to end.
  • Stations are monitored and maintained remotely.

Why choose Nexapp?

  • Indian OEM in Pune since 2014, with its own NexappOS and controller
  • Class-I local supplier under the PPP-MII Order
  • TEC MTCTE certificate 244903206 for nine Instaroute models
  • Quantum-safe on every connection: hybrid ML-KEM and ML-DSA
  • 24×7 NOC in Pune; hosted in India or self-hosted
  • 75,000+ devices deployed for 400+ enterprise and banking customers

Frequently asked questions

Is SCADA traffic encrypted over the public network?

Yes. Traffic runs in IPsec IKEv2 tunnels with hybrid post-quantum key exchange (ML-KEM), on by default.

Can stations be managed without site visits?

Yes. Configuration, firmware and signal monitoring are handled centrally from Instaroute SDWAN Lite 2.0, with an always-on management channel that works without a public IP.

Which router suits a valve or metering station?

The IR1180DM for the station cabinet: DIN-rail, two SIM slots, RS232/RS485 and GPS for location or time data. Where the cabinet has poor coverage, the IP65 IR1105-ODU-4G mounts outside on a pole and connects over Ethernet.

Will the router work with the RTUs and PLCs already at the station?

Yes. It speaks Modbus RTU/ASCII/TCP, DNP3 and IEC 60870-5-101/104, and its serial DTU carries RS232/RS485 devices over TCP or UDP, so commissioned equipment connects unchanged.

What happens on a stretch where one operator has no coverage?

Fit SIMs from two operators, chosen by survey at each station. The router uses whichever SIM meets its signal and health-check rules, so the station stays connected as long as one network reaches it.

Can SCADA traffic be kept apart from cameras and staff devices at the station?

Yes. Zone firewall and VRF segmentation put SCADA, CCTV and any office or staff traffic in separate zones on one router, and traffic crosses only where policy allows.

Read next

Planning a similar deployment?

Tell us your sites, devices and links, and a Nexapp engineer will recommend the routers and design.

Related use cases

All use cases