Energy and utilitiesSDWAN Lite
Connectivity for fuel depots and storage tank monitoring
Fuel storage has to be watched all the time: tank levels, leaks, temperature, cameras and gate access. Instaroute routers keep each depot connected over dual-SIM 4G, carry sensor protocols to the central team, and keep cameras, sensors and office traffic in separate zones so one compromised device cannot reach the others.
By Pradeep Tomar, Founder and CEO. Published , last reviewed .At a glance
- Industry
- Oil, gas and fuel storage
- Sites
- Fuel depots and storage tanks
- Devices
- Tank sensors, CCTV, access control
- Routers
- IR11004GD, IRX100-5G
How does the network connect?
Site equipment connects to an Instaroute IR11004GD, which carries the traffic over SIM 1 · Operator A and SIM 2 · Operator B inside a quantum-safe tunnel to Central monitoring team. Nothing on site accepts inbound connections.
What problem does it solve?
Many depots are outside towns, where wired links are slow to arrive or unreliable.
If the link drops, the monitoring team loses sight of the site, which is a safety and loss-prevention risk.
A depot gathers equipment from many suppliers: tank gauging, leak and temperature sensors, cameras and recorders, gate and access control, and the office PCs. Each supplier wants a way in for support, contractors on site are closely controlled, and any equipment near the tank area has to follow the site's safety rules. The network has to keep all of this separate without adding another box per supplier.
How does Nexapp solve it?
Always-on 4G connectivity for fuel depots: tank sensors, cameras and access control report to a central team, kept in separate network zones.
Cellular links that stay up
Instaroute 4G and 5G routers with dual-SIM arbitration by signal, latency or data usage, so two operators back each other up. IP65 outdoor units mount on a pole or mast where the signal is best.
Speaks the site's protocols
RS232/RS485 serial ports, a Modbus RTU/ASCII/TCP gateway, DNP3, IEC 60870-5-101/104 and an MQTT publisher, so existing controllers, RTUs and meters connect without replacement.
Cameras and sensors kept apart
Zone firewall and VRF segmentation keep CCTV, sensors and office traffic in separate zones, so one compromised device cannot reach the others.
One console for every site
Instaroute SDWAN Lite 2.0 shows the health, signal and data usage of every router, with zero-touch set-up and canary firmware rollout, for up to 100,000 devices per deployment. Run it Nexapp-hosted in India or self-hosted.
How is the site secured in the AI era?
Security is a requirement, not an add-on. AI helps attackers find exposed devices and weak access faster than ever, so this design exposes nothing, encrypts every link and checks every person who connects.
Nothing exposed to the internet
The router opens only outbound, encrypted connections. Equipment on site has no public IP and accepts no inbound connections, so automated scanners have nothing to find. Zero trust access
Quantum-safe encryption on every link
Traffic travels in IPsec IKEv2 tunnels with hybrid ML-KEM key exchange, so data captured today cannot be decrypted later. Post-quantum cryptography
Zones, not one flat network
Tank sensors, CCTV and access control sit in their own zones behind the zone firewall, so one compromised device cannot reach the rest. IoT and OT security
Access for people, not networks
Engineers and vendors connect through InstaAccess to the named equipment they support, and every session is logged. SSE and ZTNA
Signed, staged firmware
Instaroute SDWAN Lite 2.0 rolls out post-quantum-signed firmware to a canary group first, with rollback, so a bad update never reaches every site at once. Instaroute SDWAN Lite 2.0
AI that waits for your approval
NexParth AI spots problems and proposes the fix, and nothing changes until a person approves it. NexParth AI
What does the SDWAN Lite dashboard show?
One screen shows the whole fleet: total devices and online rate, WAN links and SIM cards, active alarms, a fleet map, firmware versions, configuration changes, product mix and data usage. Instaroute SDWAN Lite 2.0 manages up to 100,000 routers per deployment, hosted by Nexapp in India or self-hosted.

How is it deployed?
A typical rollout takes 4 steps, and routers configure themselves when they are powered on at site.
Design the zones
Put tank sensors, cameras, access control and office devices in separate zones.
Install the router
Connect sensors and controllers over serial or Ethernet and cameras on their own ports.
Connect to the central team
Traffic travels in encrypted tunnels over two operators to the monitoring centre.
Watch every depot
Signal, link health and data usage for each depot appear in one console.
What does the specification ask for, and how does Nexapp meet it?
These are the requirements buyers and tenders usually set for this application, and the Nexapp capability that meets each one today.
| Requirement | How Nexapp meets it |
|---|---|
| Continuous tank and camera monitoring | Dual-SIM arbitration keeps the depot online if one operator fails |
| Keep cameras away from control systems | Zone firewall and VRF segmentation on the router |
| Sensor protocols | Modbus gateway and RS232/RS485 serial ports |
| Many cameras at large depots | IRX100-5G with 5G and Gigabit Ethernet |
Which Instaroute router should you use?
For most sites, use the IR11004GD. Dual SIM with five Ethernet ports for sensors, cameras and access control.
Instaroute IR11004GD 4G router IR11004GD 4G · LTE · 2 SIM IR11004GD
Dual SIM with five Ethernet ports for sensors, cameras and access control.
- Cellular
- 4G LTE Cat 4 or Cat 6
- SIM slots
- 2
- RS232 / RS485
- RS232 and RS485
- Mounting
- Desktop or wall
Instaroute IRX100-5G 5G router IRX100-5G 5G · SA/NSA · 2 SIM IRX100-5G
5G and Gigabit where several cameras stream to the control room.
- Cellular
- 5G SA/NSA, sub-6 GHz
- SIM slots
- 2
- RS232 / RS485
- RS232 and RS485 (up to 3 ports)
- Mounting
- Desktop or wall
Also used: Instaroute SDWAN Lite 2.0
What are the benefits?
- Tank, sensor and camera data reaches the central team continuously.
- A failed SIM or operator no longer means a blind site.
- Sites are added without an engineer configuring each router.
Why choose Nexapp?
- Indian OEM in Pune since 2014, with its own NexappOS and controller
- Class-I local supplier under the PPP-MII Order
- TEC MTCTE certificate 244903206 for nine Instaroute models
- Quantum-safe on every connection: hybrid ML-KEM and ML-DSA
- 24×7 NOC in Pune; hosted in India or self-hosted
- 75,000+ devices deployed for 400+ enterprise and banking customers
Frequently asked questions
Can cameras and tank sensors share one router safely?
Yes. Zone firewall and VRF segmentation put them in separate zones on the same router.
What happens when one operator's network fails?
On dual-SIM models the router switches to the second SIM based on signal, latency or data usage.
Which router suits a fuel depot?
The IR11004GD for most depots: two SIMs, five Ethernet ports for sensors, cameras and access control, and RS232/RS485 for serial controllers. The IRX100-5G suits depots where several cameras stream to the control room and Gigabit ports are needed.
Can a tank gauging system with a serial or Modbus output connect?
Yes. The serial port carries RS232/RS485 data over TCP or UDP, and the Modbus gateway translates between Modbus RTU and Modbus TCP, so the existing gauging controller connects without replacement.
How does the central team reach depot cameras and recorders?
Over the router's encrypted tunnel to the control room, or through SD-LAN, which reaches devices behind the router without exposing them. No port is opened on the depot's SIM.
Where should the router be installed at a depot?
In the control room, office or a safe-area cabinet. The published certifications are TEC MTCTE, IEC 62443, CE and RoHS, none of which covers hazardous zones, so keep routers and outdoor units outside classified areas.
Read next
Planning a similar deployment?
Tell us your sites, devices and links, and a Nexapp engineer will recommend the routers and design.
Related use cases
Energy and utilities
4G router for substation SCADA and RTU/FRTU backhaulIndustrial 4G routers for substations, RTUs and FRTUs: IEC 60870-5-101/104, DNP3, Modbus, serial DTU and encrypted tunnels to the SCADA control centre.
Energy and utilities
Cellular backhaul for smart meters and data concentrator units4G routers for smart-meter data concentrator units (DCUs) and AMR: serial and Modbus interfaces, MQTT, encrypted tunnels and flat per-device management.
Energy and utilities
Remote monitoring and connectivity for solar plantsOne managed network for inverters, meters, weather stations and cameras across solar farms and rooftop plants, with scoped vendor access and one console.